NAND SPL Starting U-Boot ... U-Boot 1.1.6 (Apr 1 2008 - 13:52:15) Board: Ingenic PMP Ver 1.x (CPU Speed 335 MHz) DRAM: 64 MB Flash: 0 kB NAND:1024 MiB *** Warning - bad CRC or NAND, using default environment In: serial Out: serial Err: serial Net: JZ ETHERNET ### main_loop: bootcmd="mmcinit;fatload mmc 0 0x80600000 uimage;bootm" Hit any key to stop autoboot: 1  0 MMC card found MMC card is ready I'm sorry wo only surport fat16 and fat32 I'm sorry wo only surport fat16 and fat32 reading uimage filesize: 1791437, got: 1791437 1791437 bytes read ## Booting image at 80600000 ... Image Name: Linux-2.6.24.3 Image Type: MIPS Linux Kernel Image (gzip compressed) Data Size: 1791373 Bytes = 1.7 MB Load Address: 80010000 Entry Point: 80313100 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... Linux version 2.6.24.3 (ard@lennydev64) (gcc version 4.1.3 20080623 (prerelease) (Debian 4.1.2-23)) #1 PREEMPT Sat Nov 1 11:15:42 UTC 2008 CPU revision is: 02d0024f (Ingenic JZRISC) CPU clock: 335MHz, System clock: 112MHz, Memory clock: 112MHz, Peripheral clock: 112MHz JZ4730 MINIPC board setup Determined physical RAM map: memory: 04000000 @ 00000000 (usable) User-defined physical RAM map: memory: 08000000 @ 00000000 (usable) Zone PFN ranges: Normal 0 -> 32768 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: mem=128M console=ttyS0,115200n8 root=/dev/ssfdca1 rw noatime Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes Synthesized clear page handler (25 instructions). Synthesized copy page handler (44 instructions). Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour dummy device 80x25 console [ttyS0] enabled Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 125668k/131072k available (3105k kernel code, 5316k reserved, 743k data, 164k init, 0k highmem) Mount-cache hash table entries: 512 net_namespace: 64 bytes NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered Power Management for JZ yaffs Nov 1 2008 11:12:19 Installing. io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered jzlcd use 1 framebuffer: jzlcd fb[0] phys addr =0x07d00000 LCDC: PixClock:9066551 LcdClock:27955200 Console: switching to colour frame buffer device 60x34 fb0: jz-lcd frame buffer device, using 256K of video memory PCF8563 RTC installed !!! JzSOC: char device family. Jz generic touch screen driver registered AK4182 touch screen driver initialized Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled ¿®–¥…±á250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A serial8250: ttyS1 at MMIO 0x0 (irq = 8) is a 16550A serial8250: ttyS2 at MMIO 0x0 (irq = 7) is a 16550A serial8250: ttyS3 at MMIO 0x0 (irq = 6) is a 16550A RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: module loaded WARNING: There is not MAC address, use default .. Linux video capture interface: v2.00 Driver 'sd' needs updating - please use bus_type methods NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 57 at 0x00720000 Bad eraseblock 58 at 0x00740000 Bad eraseblock 59 at 0x00760000 Bad eraseblock 60 at 0x00780000 Bad eraseblock 61 at 0x007a0000 Bad eraseblock 62 at 0x007c0000 Bad eraseblock 63 at 0x007e0000 Bad eraseblock 64 at 0x00800000 Bad eraseblock 65 at 0x00820000 Bad eraseblock 66 at 0x00840000 Bad eraseblock 67 at 0x00860000 Bad eraseblock 68 at 0x00880000 Bad eraseblock 69 at 0x008a0000 Bad eraseblock 70 at 0x008c0000 Bad eraseblock 71 at 0x008e0000 Bad eraseblock 72 at 0x00900000 Bad eraseblock 73 at 0x00920000 Bad eraseblock 74 at 0x00940000 Bad eraseblock 75 at 0x00960000 Bad eraseblock 76 at 0x00980000 Bad eraseblock 77 at 0x009a0000 Bad eraseblock 78 at 0x009c0000 Bad eraseblock 79 at 0x009e0000 Bad eraseblock 128 at 0x01000000 Bad eraseblock 136 at 0x01100000 Bad eraseblock 154 at 0x01340000 Bad eraseblock 252 at 0x01f80000 Bad eraseblock 282 at 0x02340000 Bad eraseblock 560 at 0x04600000 Bad eraseblock 636 at 0x04f80000 Bad eraseblock 670 at 0x053c0000 Bad eraseblock 692 at 0x05680000 Bad eraseblock 698 at 0x05740000 Bad eraseblock 1150 at 0x08fc0000 Bad eraseblock 1675 at 0x0d160000 Bad eraseblock 2042 at 0x0ff40000 Bad eraseblock 3280 at 0x19a00000 Bad eraseblock 5433 at 0x2a720000 Bad eraseblock 6528 at 0x33000000 Bad eraseblock 7546 at 0x3af40000 Bad eraseblock 7751 at 0x3c8e0000 Creating 1 MTD partitions on "NAND 1GiB 3,3V 8-bit": 0x00300000-0x08000000 : "NAND ROOTFS partition" jz-ohci jz-ohci.0: JZ OHCI jz-ohci jz-ohci.0: new USB bus registered, assigned bus number 1 jz-ohci jz-ohci.0: irq 13, io mem 0x13030000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usb 1-2: new full speed USB device using jz-ohci and address 2 usb 1-2: configuration #1 chosen from 1 choice hub 1-2:1.0: USB hub found hub 1-2:1.0: 4 ports detected usb 1-2.3: new low speed USB device using jz-ohci and address 3 usb 1-2.3: configuration #1 chosen from 1 choice usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice JzSOC Watchdog Timer: timer margin 60 sec JZ SD/MMC card driver registered usbcore: registered new interface driver hiddev input: CHESEN PS2 to USB Converter as /class/input/input0 input: USB HID v1.10 Keyboard [CHESEN PS2 to USB Converter] on usb-jz-2.3 input: CHESEN PS2 to USB Converter as /class/input/input1 input: USB HID v1.10 Mouse [CHESEN PS2 to USB Converter] on usb-jz-2.3 usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. Root-NFS: No NFS server available, giving up. VFS: Unable to mount root fs via NFS, trying floppy. VFS: Cannot open root device "ssfdca1" or unknown-block(2,0) Please append a correct "root=" boot option; here are the available partitions: 1f00 125440 mtdblock0 (driver?) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)